Silicon assistant carbothermal reduction for SiC powders

The silicon assistant method to increase the reaction yield of carbothermal reduction of silica at a lower temperature is reported. The effect of silicon on the carbothermal reduction process has been investigated in detail. Compared with traditional reduction, the introduction of silicon can change the reaction path and further increase the conversion of silicon carbide at a lower temperature. It is considered that the assistant reduction consists of three steps: vaporizing and melting of silicon, formation of silicon monoxide, and synthesis of silicon carbide. The morphology of the synthesized SiC powders through the silicon assistant method can be affected apparently by the experimental temperature.     

SiC/Si-W-Mo coating for protection of C/C composites at 1873 K

In order to prevent carbon/carbon composites from oxidation at 1873 K, an efficient oxidation protective SiC/Si-W-Mo coating was prepared by a two-step pack cementation technique. The microstructures and the phase composition of the as-received multi-coating were examined by scanning electron microscopy （SEM） and X-ray diffraction （XRD）. It is seen that the compact multi-coating is composed of α-SiC, Si, and （WxMO1-x）Si2. Oxidation test shows that, after oxidation at 1873 K in air for 102 h and thermal cycling between 1873 K and room temperature for 10 times, the weight loss of the SiC/Si-W-Mo coated C/C composites is only 0.26%. The invalidation of the multi-coating is attributed to the formation of penetrable cracks in the coating. 2008 University of Science and Technology Beijing. All rights reserved.     

Hydrogen-induced cracking behaviors of Incoloy alloy 825

The effect of hydrogen on the fracture behaviors of Incoloy alloy 825 was investigated by means of slow strain rate testing (SSRT).Hydrogen was introduced into the sample by electrochemical charging.The results show that surface microcracks form gradually during aging at room temperature when desorption of hydrogen takes place after hydrogen charging at a current density of 5 mA/cm 2 for 24 h.SSRT shows that the increase of ductility loss is significantly obvious as the hydrogen charging current density inc...     

3D Modeling of the preparation process of metal rubber material

Based on the analysis of the preparation of metal rubber (MR) and two pivotal hypotheses,the uniform distribution and the unaltered topological structure of wires in the radial direction of columns in the punch process,a 3D parametrical model was established based on four approaches:helix-making,planar roughcast-weaving,planar roughcast-rolling,and 3D roughcast punching.In the modeling process,5 lattice types of weave patterns in planar roughcast were put forward,and 10 quantificational modeling parameters ...     

Relationship between the microstructure and reaction performance of aluminosilicate

A systematic study was conducted to comprehend the mechanism of thermal activation of silica-alumina materials by using 29 Si and 27 Al magnetic angle spinning nuclear magnetic resonance (MAS NMR) spectroscopy.The reaction performance of silica-alumina-based materials with different molar ratios of Si/Al,which were thermally activated,was also investigated.With the increase in calcining temperature,the coordination of Al in metakaolin becomes four,five,and six firstly,and then transforms completely to four ...     

Water modeling of molten steel flow in a multi-strand tundish with gas blowing

Fluid flow characteristics in a four-strand tundish with gas blowing were studied by water modeling experiments.It is found that gas blowing can greatly improve the flow characteristics in the tundish with a turbulence inhibitor.It dramatically increases the peak concentration time,and greatly decreases the dead volume,and reduces the minimum residence time.The gas blowing location,gas flow rate,and porous plug area greatly influence the flow characteristics in the tundish;the gas blowing location near t...     

Decarburization rate of RH refining for ultra low carbon steel

The decarburization behaviors of ultra low carbon steel in a 210-t RH vacuum degasser were investigated under practical operating conditions.According to the apparent decarburization rate constant (KC) calculated by the carbon content in the samples taken from the hot melt in a ladle at an interval of 1-2 min,it is observed that the total decarburization reaction period in RH can be divided into the quick decarburization period and the stagnant decarburization period,which is quite different from the tradit...     

Dependence of domain wall structures on repetition n in[Pt（0.5 nm）/Co（0.4 nm）]n/NiO（1.1 nm）/[Co（0.4 nm）/Pt（0.5 nm）]n multilayers

The magnetic force microscopy and a sample vibrating magnetometer have been used to investigate the domain structure in two antiferromagnetically coupled Co/Pt multilayers.In the antiferromagnetic coupled[Pt(0.5 nm)/Co(0.4 nm)]_n/NiO(1.1 nm)/[Co(0.4 nm)/Pt(0.5 nm)]_n multilayers with perpendicular anisotropy,the antiferromagnetic interlayer coupling strength increases linearly with the repetition number n in Co/Pt multilayers.In demagnetized states,relatively shifted domain walls in the two Co/Pt multila...     

Particle simulation of the failure process of brittle rock under triaxial compression

In order to investigate the failure process of brittle rock under triaxial compression through both experimental and numerical approaches, the particle simulation method was used in numerical simulations and the simulated results were compared with those of the experiment. The numerical simulation results, such as fracture propagation, microcrack distribution, stress-strain response, and damage patterns, were discussed in detail. The simulated results under various confining pressures (0-60 MPa) are in good...     

Gearbox fault diagnosis of rolling mills using multiwavelet sliding window neighboring coefficient denoising and optimal blind deconvolution

Fault diagnosis of rolling mills, especially the main drive gearbox, is of great importance to the high quality products and long-term safe operation. However, the useful fault information is usually submerged in heavy background noise under the severe condition. Thereby, a novel method based on multiwavelet sliding window neighboring coefficient denoising and optimal blind deconvolution is proposed for gearbox fault diagnosis in rolling mills. The emerging multiwavelets can seize the important signal proce...